A few weeks ago I reviewed the BetaFPV Pavo30 drone that was based on this Toothpick F722 flight controller. Due to some accident, a few of the MOSFETs on the board fried and I decided to order a new one.
In a nutshell, a flight controller (aka FC) is the brain of the drone. Its central processor receives data from a wide range of onboard sensors (Gyroscope, Accelerometer, Barometer, and Compass), as well as pilots’ commands, and controls the speed of each motor directly or via an ESC to make the aircraft move as instructed.
The BetaFPV Toothpick F722 is a versatile and powerful flight controller designed for 3-5″ quadcopters (it has 4 motor outputs). It can be used on CineWhoop style drones as well as on Thootpick ones. Thanks to the six UART ports, can be interfaced with a wide range of devices, such as GPS, LED boards, VTX, and FPV camera.
BetaFPV Toothpick F722 review
Disclosure: I received this flight controller as part of a product review collaboration with BetaFPV. Technical specs and quality may vary according to the manufacturer’s reliability, so I cannot guarantee that you will get a product that is identical as seen in my article.
The Toothpick F722 flight controller comes in a nice plastic box with 14AWG silicone XT60 power cable, RF filter capacitor, 6-Pin Connector for DJI Digital VTX, and mounting accessories (4 pieces of M2x10mm screws with nuts and silicone grommets) included.
The board measures 33x33mm and it has a 25.8×25.8mm mounting pattern. The arrow near the STM32F722 high-performance CPU indicates the installation direction of the FC. It has large soldering pads for motors and safe space between battery wiring holes. Additionally, you have dedicated holes for the 470uF 35V capacitor. There is a standard micro USB port for firmware upgrade and configuration.
Near the MPU6000 motion processing unit (3-axis gyroscope + 3-axis accelerometer) there are two status LEDs (Power and Mode).
Its integrated BLHeli_S 4-in-1 ESC is rated at 35A with 40A peeks. It has six (3 on each side of the board) TPN2R304PL MOSFETs for each channel.
BetaFPV Toothpick F722 specs
- CPU: STM32F722RET6;
- Six-Axis gyro: MPU6000 (SPI connection);
- Firmware version: BetaFlight_4.2.x_BETAFPVF722;
- OSD: Built-in BetaFlight OSD (OSD chip: AT7456E);
- Support programmable LED like WS2812 etc;
- 6-pin connector for DJI Digital\Caddx VTX;
- Built-in current sensor;
- Integrated 35A ESC:
- Continuous current: 35A;
- Peak current: 40A;
- ESC firmware: BLHeli_S;
- Signal support: PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, and Dshot600.
- Input voltage: 2S-6S Lipo;
- Mounting pattern: 26 x 26mm;
- Size: 33 x 33mm;
- Weight: 7 grams (without any cable).
Wiring pinout (wiring diagram)
The BetaFPV’s Toothpick F722 AIO flight controller has battery input (+-), 4 motor outs, 2×5 pin raws (TX5/GND, CAM/5V, VTX/LED, GND/BUZZ+, and 5V/BUZZ-), and a 5/6 pin pads (3.3V, TX3, 5V, GND, RX1, and TX1 / GND, 5V, RX3, 5V, GND, RX6, and TX6). It also has a 6pin connector for DJI\Caddx digital VTX (SBUS\RX3, GND, RX2, TX2, GND, and BAT+).
Price and availability
Priced for $84.99, it isn’t the cheapest flight controller right now. It has almost half the price of a drone that comes with the F722 AIO 35A FC onboard. You can order it directly from BetaFlight or other popular RC hobby shops.
Visitor Rating: 1 Stars
Hello Firstquadcopter Team,
In addition to Oscar Liang’s Blog, I like to check out your website for tips and tricks related to FPV. And just to be up to pace with what’s going on in the hobby. So thank you for all you guys share.
I am writing this email for a different reason, I noticed in one of your story last year :
https://firstquadcopter.com/reviews/betafpv-toothpick-f722-review/
You mentioned that a few FETs got fried. I happen to be trying to find these FETs as I want to try and repair my FC.
I’m currently in medical school and FPV helps me stay grounded and alleviate stress. I mostly try finding good deals on ebay to keep the hobby not breaking my wallet. And I realize that it’s possible to repair these costly electronics with enough persistence and perseverance.
I don’t know if it’s possible or something you are inclined to do. But if you have that particular FC or other FCs or ESCs which are burnt/damaged. And if they are no use to you, let me know if you’d be happy to ship them to me.
I can pay the shipping cost happily. And I’m trying my hand at fixing my boards. At best a rookie, but I wanna learn to fix FCs and ESCs. Just because I’m in medical school, I don’t wanna limit myself to the human body. I love the parallels they teach us at the cellular level and now I see how these electronics are their own beautiful world .
Let me know what you think :)
Thanks for your time and energy
Warm Regards
Karan
No baro on this board
To avoid wasting time on a board that comes out defective by manufacturer
defective?? Mine was OK, just I needed to remap the motor channels
This is a nice toothpick flight controller. It has all of the features needed for a modern flight controller. Great work BetaFPV!
This BetaFPV FC is a great product and full of nice add-ons including digital FPV plug
Why should we connect to USB and BF before soldering?
You mention it has a barometer. Where?
Visitor Rating: 5 Stars
Visitor Rating: 5 Stars
Visitor Rating: 4 Stars
Visitor Rating: 4 Stars